Skip to content

Stair Calculator

Use this stair calculator to estimate how many steps you need between floors, find the riser height and tread depth, and check whether a straight flight fits the space you have.

Where to measure

Side view of a stair flight Total rise spans the lower and upper finished floors. Total run spans the first tread edge and the upper floor edge. Riser height is measured vertically and tread depth horizontally between consecutive tread edges. Upper floor Lower floor Total rise Total run Tread depth Riser height
Illustration only. See your results for the calculated dimensions and step count.
Vertical measurements
The two finished floors are your reference points. Enter the vertical difference between them. For example, use 105.5, 105 1/2, or 8 ft 9 1/2 in.
Enter a whole number of at least 2.
Horizontal measurements
From the front edge of one tread, measure straight back to the front edge of the next tread up.
Start where the first tread will begin and measure horizontally to the edge of the upper floor. Allow for landings separately.

How to Use the Stair Rise and Run Calculator

Start with Total rise, the vertical distance from the finished surface you stand on at the bottom to the finished surface you step onto at the top. If your drawing already gives a riser count, enter that number. Otherwise, enter the tallest riser you want to consider. The calculator divides the total rise by that limit and rounds the count up to the next whole riser when needed.

Choose the horizontal measurement you already know. With Tread depth, the form finds the total run and can compare it with the available space. With Target run, it works backward from the length you assign to the flight and finds the depth of each tread. You can enter inches in one field and feet in another. For a measurement like 8 ft 9 1/2 in, enter it as written or select inches and enter 105 1/2.

After you calculate, keep the number of risers and the number of treads together on your sketch. A note that says “14 steps” can be read two ways. Record “14 risers, 13 treads” and mark which floor is at each end. The stair rise run calculator uses the same floor-to-floor convention for both input modes, so you can switch between a chosen tread depth and a target run without changing how the steps are counted.

How the Stair Riser Height Calculator Counts Steps

Measure vertically between the two finished walking surfaces. At an open stairwell, use a level to mark the height of the upper finished floor on a nearby wall. Measure straight down from that mark to the lower finished floor. Enter that vertical reading in the stair height calculator.

On a site with unfinished floors, write down which layers are still due on each level. If your measurement starts and ends at bare subfloor, add the thickness of the upper finish assembly and subtract the thickness of the lower one. Raising the upper surface increases the climb. Raising the lower surface reduces it. Include underlayment where it affects the planned walking surface. If the finish at one end changes during the job, update that elevation and run the calculation again before using the dimensions on a drawing.

Picture the first movement from the lower floor onto the first tread. That movement uses one riser. Each tread after that has another riser. The last riser brings you directly onto the upper floor. That leaves one fewer separate tread than risers in the stair step calculator. The vertical distance is split evenly across all the risers. For 105 in of rise and 14 risers, that gives 7.5 in per riser and 13 treads.

How the Stair Tread Calculator Works

Tread depth is the horizontal distance from one nosing to the next. The nosing is the front edge of the tread. A tread board can extend back under the next riser or project over the riser beneath it. Its overall width can therefore differ from the spacing between two nosings. Use that spacing for the layout. For the actual cut dimensions, refer to the detail drawing for the tread and riser joint.

In tread depth mode, the calculator multiplies the number of treads by that spacing. In target run mode, it divides the planned run by the tread count. For the same 14 risers and 13 treads, a run of 130 in gives 10 in per tread. If you change the riser count while holding the target run at 130 in, you also change the number of treads sharing that length. Read the new tread depth before comparing that option with your earlier drawing.

Check Available Space With the Stair Run Calculator

Mark where the front edge of the first tread will sit. From that point, take a level measurement along the flight to the edge of the upper finished floor. Project both points onto the same level when using a tape. If the lower end must stop at a particular line, such as the edge of a separate landing, measure from the proposed first tread edge there. Reserve landing space separately before entering the length available to the flight.

Try Load example and calculate. With a total rise of 105 in, 14 risers leave 13 treads. At 10 in per tread, the flight takes up 130 in horizontally. In 132 in of available space, that leaves 2 in. A run and available space of exactly 130 in would fit exactly. With 15 risers, the same rise is divided into 7 in lifts, but now there are 14 treads. Keeping each tread 10 in deep makes the run 140 in, which needs 8 in more than the space provided.

Use the available-space result for the flight itself. If you are pricing the finish on a separate upper landing, calculate the square footage of the landing from its own length and width. For an outdoor stair with a concrete pad specified at the bottom, estimate how much concrete you need for the bottom landing using the pad dimensions and thickness from the project plans.

Compare Options With the Stair Layout Calculator

When tread depth is fixed, the comparison shows the chosen count and its nearest neighbors starting at two risers. Read down the run figures to see what each added tread costs in horizontal space. If you entered your own maximum riser height, the comparison marks any option that exceeds it. That allows you to see why a shorter option was excluded even when it fits between the points you measured.

Use the stair dimensions calculator diagram to carry the same reference points onto your sketch. Total rise spans both finished floor levels. Total run starts beneath the first tread edge and ends beneath the edge of the upper floor. The short vertical arrow spans one riser height. The short horizontal arrow spans the distance between two consecutive front edges. The drawing uses a few steps to show the dimensions clearly. The text beside it gives the count and sizes for your flight.

What the Stair Pitch Calculator Measures

Draw a line through the nosings in side view. From one front edge to the next, the line climbs by one riser height and travels forward by one tread depth. The pitch is the arctangent of that ratio. A 7.5 in riser and a 10 in tread make a ratio of 0.75 and an angle of about 36.9°. Using the full height and full run would mix 14 vertical intervals with only 13 horizontal ones in this example. Keep the per-step dimensions together when checking the angle.

What to Check on the Project Drawings

Check where the top and bottom landings meet the flight. Trace the stair in section to check headroom where the flight passes the edge of the floor opening or beneath a beam. Mark the location of handrails and guards, and check the connection details that show how the flight attaches at each floor. Confirm local requirements for the project and have the stringers, their supports, and the connections specified separately. The calculator covers the geometry of one straight flight.

Frequently Asked Questions

Why does the upper floor change the number of treads?

Your last move is from the highest separate tread onto the upper finished floor. That move adds a riser, and the floor itself provides the surface for your foot. Count only the intermediate surfaces as separate treads.

Where should I start and end the height measurement?

Start at the finished floor beside the first riser and end at the finished surface above the final riser. If the lower landing is outside and the ground slopes, use the planned elevation at the base of the flight. Record that point so a later measurement starts from the same place.

What if my straight flight needs more space?

Check that you measured to the same edges used for total run. Then compare the nearby riser counts and see what tread depth the available run would yield. If the resulting dimensions don’t work for the project, review the opening and the flight arrangement together before settling on a layout.

Does the total run include a landing?

The run ends at the edge where you step onto the upper floor and starts at the front edge of the first tread. Measure any floor or landing beyond those edges in its own space. A turn or intermediate landing calls for separate flight measurements.