Calculate again before downloading a PDF.
Baseboard estimate
How to Use the Baseboard Linear Feet Calculator
Choose Rectangular Room when the walls form a rectangle and you can account for the gaps by subtracting their widths. Enter the room length and width once. Use a separate deduction row for each different opening size or section without trim. If two doorways each leave a 36-inch gap, enter 36 in with a quantity of two. If one is narrower, give it a row of its own so the calculation uses both actual widths.
Choose Wall Runs for an L-shaped room, a bay window, or several damaged pieces you plan to replace. Add each continuous stretch of wall that will get trim. Give the rows names you can match to your sketch, such as “Window wall” or “Hall door, left.” If a door interrupts a 12 ft wall and leaves 4 ft on one side and 5 ft on the other, enter those two runs. The 3 ft doorway is already out of the total.
Each measurement can use feet or inches. For a wall that measures 8 ft 6 in, enter 8.5 ft or 102 in. When your tape reads 8 ft 7 in, entering 103 in preserves the measurement without rounding a repeating decimal. Keep your notes in the units you used at the wall so you can double-check what went into the form.
If you’re replacing the floor and the trim together, use the Flooring Calculator for the surface area you plan to cover. For baseboards, measure the length of the finished walls where the trim will run. Two rooms with the same floor area can have different wall lengths, and a doorway changes the trim measurement even if the flooring continues through it.
How to Calculate Linear Feet for Baseboards
Measure at the bottom of the finished wall, where the new baseboard will sit. For a rectangular room, add the length and width, then double that sum to get the perimeter. Measure from finished corner to finished corner, with the tape following the wall. If opposite walls differ enough to matter for your order, measure all four sides and enter the lengths individually in Wall Runs.
Subtract the width of every interruption included in the perimeter where no baseboard will go. At a doorway, check the span between the points where the baseboard will meet the door casing. The gap at the bottom of the wall can differ from the nominal width of the door. Check built-in cabinets, fixed shelving, fireplace surrounds, and closet openings the same way. Subtract only the part that actually interrupts the trim. Include the walls inside a closet if they are in scope, measuring those runs separately.
If the project also involves wall repairs, use the Drywall Calculator to estimate the sheets for that work. Recheck your trim measurements after the drywall and door casing are in place. A new return, thicker wall finish, or changed casing can move the point where a board starts or stops.
For a room with an alcove or a bump-out, walk the room in one direction and sketch each change in direction. Record the face of the wall in the alcove and both sides that lead into it, wherever trim will be installed. Measure angled walls along the angle. At each doorway, mark where the trim stops on both sides. Label those separate lengths in the form and compare the rows with the sketch before you calculate. This also gives you a record of the cuts you’ll need later.
How Many Feet of Baseboard Do I Need?
Take a 12 × 15 ft room with two door openings, each 36 in wide. The perimeter is 2 × (12 + 15), or 54 linear ft. Each opening removes 3 ft, for 6 ft of total deductions. That leaves 48 linear ft of finished wall to cover. With a 10% cutting allowance, add 4.8 ft to get 52.8 linear ft.
With 8 ft boards, 52.8 ÷ 8 gives 6.6, which rounds up to seven whole boards. Seven boards supply 56 linear ft. That’s 3.2 ft more than the length you need with the allowance already included. At an example price of $16 per board, the material cost is $112.00. A quote of $2.00 per linear foot also gives $112.00 if you buy those same seven whole boards and pay for all 56 ft. Without a board length, the estimate uses 52.8 ft at $2.00, or $105.60.
Select Load example to enter those values in Rectangular Room. In Wall Runs, the example represents the same room with both doors on one 15 ft wall. The three uninterrupted stretches on that wall are 2, 3, and 4 ft. Add the opposite 15 ft wall and both 12 ft walls to reach the same 48 linear ft. The wall-by-wall version also shows which runs are longer than an 8 ft board. Calculate and select Download PDF to keep a copy of either estimate.
How the Baseboard Trim Calculator Estimates Whole Boards
Choose a cutting allowance based on your work. A room with several short returns and outside corners may give you fewer reusable offcuts than one with long, straight walls. If you already set aside material for mistakes and test cuts, you can enter zero. The calculator applies the allowance to your clean footage once, then divides by the board length if you supply one. The extra footage from rounding to whole boards appears separately so you can see what comes from the allowance and what comes from the way the boards are sold.
The board count is an estimate based on total length. For example, three 5 ft runs need 15 ft of trim. Two 8 ft boards give you 16 ft in total, but if each run needs a single piece, each board yields only one 5 ft piece. The two 3 ft offcuts cannot make a third uninterrupted piece. You’d need a third board even with enough footage on paper. Check where joints can go, which ends need corner cuts, and whether a leftover piece is long enough after trimming its ends.
Before ordering, compare the longest runs on your sketch with the actual lengths your supplier stocks for the profile you chose. For any run longer than a board, plan a joint or use a longer board if available. Check inside and outside corner cuts and allow for damaged ends or an offcut with a miter that faces the wrong way for the next piece. When blending a repair into existing trim, bring a sample or take a clear photo of the profile and verify its height and thickness as well as its length.
Start your cut list with the runs that have to come from the longest boards. Write down which ends meet casing and which turn a corner. Then match the shorter runs to the offcuts those long pieces leave behind. If you’re buying painted and stain-grade trim for different rooms, keep the cut lists separate. An offcut that fits by length still has to match the profile and finish in that room.
Enter the material price as quoted. For a price per board, the calculator needs the length of that board to estimate the number to buy. For a price per linear foot, it displays the length being charged. When you specify a board length, the charge is based on the full purchased length of those whole boards. If you leave the length blank, the estimate uses the requirement with allowance. Check any supplier minimums, bundles, delivery charges, and taxes separately.
Frequently Asked Questions
Can I use this baseboard length calculator for one damaged section?
Yes. Choose Wall Runs and enter the length you plan to remove and replace. If the repair will run from a doorway to a corner, measure between those finish points. Check whether you can use a matching piece on hand before ordering a full board, especially if the original profile is hard to match.
Can I use the baseboard estimator for several rooms at once?
Yes, if you’re buying one profile in the same board length and at the same price. In Wall Runs, include the room name in each label so you can trace the footage back to your sketch. For different profiles or lengths, calculate each order separately and check whether the offcuts can be reused within that group.
Can the baseboard molding calculator also estimate shoe molding?
Yes. Measure the runs that will get shoe molding and enter its board length and price in a separate calculation. Check the stops and returns for that profile. They may differ at a cabinet, hearth, or door where the baseboard and shoe molding terminate at different points.
Should I subtract the width of furniture?
Keep the wall length behind movable furniture if you’ll install baseboard there. For a permanent cabinet or built-in, look at the installation detail. If the cabinet goes directly against the wall and the trim stops at its sides, subtract that span. Measure any exposed side that will receive the same trim as a separate run.
