Skip to content

Gravel Calculator

Estimate volume, approximate weight, and cost from dimensions or a known area. Enter your layer depth and supplier’s pricing to plan an order.

Plan your gravel order

Measure the area

For a finished compacted layer, confirm the loose quantity with your supplier. Diagram not to scale.

Uniform gravel layer with length, width, and vertical depth.lengthwidthdepth
Density for weight estimate

100 lb/cu ft (1.35 US tons/cu yd). Approximate weight estimate; confirm your material’s bulk density.

About the planning density

A rough reference for landscape and pea gravel, not a product specification. The source does not specify moisture or compaction conditions.

Optional extra for measurement variation or losses.

Extra material is not a compaction factor.

Blank = unknown; 0 = no charge.
Delivery and other supplier fees
Order total for fees. Blank = unknown; 0 = no fees.

What Can You Use the Gravel Calculator For?

Planning a gravel garden path or a level parking area? Perhaps you want to add crushed stone around flower beds or along a fence. Before you start, estimate how much material you’ll need so you can avoid buying more than necessary. Our free gravel calculator helps you plan your order. Here’s how to use it.

How Much Gravel Do I Need?

You need the area and layer depth; estimating weight also requires bulk density. This gravel estimator works with dimensions or a known square footage.

  1. Enter length and width in feet, or choose I know the area and enter square feet. For decimal feet, 10 ft 6 in = 10.5 ft.
  2. Enter the intended layer depth in inches.
  3. Check the bulk density and add extra material if needed for measurement variation or losses.
  4. Choose cubic yards or US tons to match your supplier’s quote. Enter the order increment, unit price, and delivery fees if known, then select Calculate.

For an irregular footprint, split it into simple shapes with the Square Footage Calculator and add their areas.

Cubic Yards vs. Tons

Cubic feet and cubic yards measure volume; US short tons measure weight. 1 cu yd = 27 cu ft, and 1 US short ton = 2,000 lb. Results show both volume units, so you can use the gravel calculator for cubic feet or yards without switching modes.

Volume in cubic yards = area in square feet × depth in inches ÷ 324. The weight estimate then depends on bulk density. A heavier material needs more tons for the same space.

Material Density and Extra Allowance

The built-in 100 lb/cu ft is an approximate planning value. Crushed gravel and other products vary with particle size, moisture, and loose or compacted condition. For an order by weight, use your supplier’s bulk density, which includes the spaces between stones, rather than the density of solid rock.

The extra percentage increases measured volume once; weight uses that increased volume. Supplier rounding then adjusts the order to the selected increment. Neither adjustment models compaction.

Example: How Many Yards or Tons of Gravel Do I Need?

For a 10 × 12 ft area at 3 in deep, enter 10% extra and an illustrative bulk density of 100 lb/cu ft. This depth is an example, not a construction recommendation.

ResultAmount
Area120 sq ft
Volume without extra30 cu ft ≈ 1.11 cu yd
Volume with 10% extra33 cu ft ≈ 1.22 cu yd
Approximate weight with extra1.65 US tons

These are two alternative ways to order the same calculated requirement: a 0.25 cu yd increment gives 1.25 cu yd, while a 0.5 US ton increment gives 2 US tons. Use the option your supplier sells; do not add the two quantities.

Estimating Gravel Cost

With illustrative prices, 1.25 cu yd × $50 = $62.50 for material. With $75 delivery, the estimated total is $137.50. If buying by weight, enter the quoted price per US ton instead. Unentered taxes, labor, and other charges are excluded.

Open What if the layer were 1 inch deeper? to compare material quantity and cost at a greater depth.

Coverage of 1 Cubic Yard of Gravel

This is geometric coverage of an even layer without compaction or losses. Depths are shown for comparison.

Layer DepthArea Covered
1 in324 sq ft
2 in162 sq ft
3 in108 sq ft
4 in81 sq ft
6 in54 sq ft

For a known supply: coverage in sq ft = cubic yards × 324 ÷ depth in inches. The form above calculates material needed from an area, rather than coverage from a supplied quantity.

Before You Order

  • Confirm the material and intended layer depth.
  • Confirm bulk density if ordering by weight.
  • Check the order increment and minimum quantity.
  • Confirm delivery and other charges.

For a patio foundation, use the Paver Base Calculator to estimate aggregate base and bedding separately.

Frequently Asked Questions

Can I calculate without a density?

Yes. Choose supplier density and leave it blank for volume and cubic-yard ordering. Weight and ton-based orders need a density.

How many tons are in a cubic yard?

At 100 lb/cu ft, one cubic yard weighs approximately 1.35 US tons. Your material’s bulk density determines the actual conversion.

Can I use an irregular area?

Yes. Add nonoverlapping areas at the same depth. For sections with different depths, calculate each separately, add their unrounded volumes, and apply supplier rounding to the combined order.

Should I always add 10%?

No. Choose an allowance based on measurement accuracy and handling losses. The default is 0%.

Why is the combined cost missing?

Enter both a material price and delivery fees. Enter 0 for free delivery. A ton-based order also needs a density.