Estimated operating current
- Calculated current
- Electrical input power
- Supply voltage
- Supply mode
- Power factor
- Formula with your values
This is an operating-current estimate, not a wire or breaker selection. Load type, continuous operation, installation conditions, and applicable requirements still need review. Starting current is not included, and this result does not confirm that an existing circuit is suitable.
When this estimate helps
While making an appliance list for a kitchen remodel, you may know a device’s wattage before you know its current. A watt to amp calculator lets you estimate that operating current for the stated voltage and power factor. You can also compare equipment specifications or check a steady DC load on a low-voltage supply.
Use the wattage for the operating condition you want to assess. A cycling heater, variable-speed tool, or adjustable appliance can draw different current at different settings. This calculation does not add up a home’s demand or establish whether an existing circuit can supply a new appliance.
How to use the calculator
- Choose DC, single-phase AC, or balanced three-phase AC to match the supply and load.
- Enter positive electrical input power in W or kW. Changing the unit converts a valid number: 1,500 W becomes 1.5 kW.
- Enter the voltage across the load. For AC, use RMS voltage; for three-phase, use line-to-line voltage and the total active power of all three phases. Presets are shortcuts, not confirmation of your supply.
- For AC, enter the equipment’s power factor at that operating condition. The initial 1.0 assumes a resistive load; replace it when the equipment data or measurements specify another value.
- Select Calculate. Review the inputs and substituted formula, then use Download PDF to save that calculation. Any input change requires a fresh calculation before export.
How to Calculate Amps From Watts
To convert watts to amps, divide active electrical input power by the voltage and the factors that apply to your circuit. These equations return steady DC current or AC RMS current.
- DC: I = P / V.
- Single-phase AC: I = P / (V × PF).
- Balanced three-phase AC: I = P / (√3 × VLL × PF).
P is input active power in watts; V is voltage in volts; PF is power factor; I is current in amperes. Convert kW to W by multiplying by 1,000. For three-phase AC, P is the total across all phases, VLL is RMS voltage between lines, and I is RMS current in each line, not the sum of three currents. This mode assumes balanced loads and sinusoidal supply voltage; unbalanced systems and distorted inverter outputs need a more detailed assessment.
Checked examples
| Mode and inputs | Calculation | Current |
|---|---|---|
| DC: 1,500 W, 120 V | 1,500 / 120 | 12.5 A |
| Single-phase: 1,500 W, 120 V, PF 1 | 1,500 / (120 × 1) | 12.5 A |
| Single-phase: 1,500 W, 120 V, PF 0.8 | 1,500 / (120 × 0.8) | 15.625 A |
| Single-phase: 2,400 W, 240 V, PF 1 | 2,400 / (240 × 1) | 10 A |
| Balanced three-phase: 11 kW, 400 V line-to-line, PF 0.9 | 11,000 / (√3 × 400 × 0.9) | About 17.64 A per line |
The 120 V and 240 V examples illustrate common US equipment voltages. The 400 V example demonstrates the three-phase formula; always use your equipment’s actual supply voltage.
What Power Factor changes
Power factor is active power divided by apparent power. At the same input watts and voltage, a lower PF means more RMS current. In the 1,500 W example, changing PF from 1 to 0.8 increases current from 12.5 A to 15.625 A.
PF = 1 is an assumption suitable for an ideal resistive load, such as a simple heating element. Motors, electronic power supplies, and controlled heaters may differ. Use equipment specifications or measured true power factor at the relevant load. For nonlinear equipment, displacement power factor or cos φ alone may omit distortion effects. Power factor is not motor efficiency. The accepted range here is greater than 0 and no more than 1; DC does not use PF.
Input watts, motor output, and VA
Enter the active electrical power drawn at the supply. A motor’s mechanical output rating applies at the shaft. Divide that output in watts by efficiency, expressed as a decimal, to find electrical input watts. This calculator has no efficiency input, so obtain input watts before calculating.
Volt-amperes (VA) describe apparent power. They are not interchangeable with input watts when PF is below 1. For a single-phase load with a known VA rating, current is VA / V; for a balanced three-phase load it is VA / (√3 × VLL). Do not enter a VA rating in the watts field.
Before choosing a circuit
The result estimates operating current from your inputs. It does not select a wire or circuit breaker. Load type, continuous operation, installation method, conductor and termination ratings, temperature, grouping, voltage drop, and applicable requirements can change the circuit design. Motors and other loads with starting current need additional checks; steady operating amps do not describe startup.
For a supported 120 V or 240 V single-phase, two-wire home branch circuit, the Wire Size Calculator can compare supported AWG sizes using load, breaker, distance, and installation conditions. Its resistive-load model evaluates voltage drop; general AC loads do not receive a combined size recommendation. It excludes DC, three-phase, motors, HVAC, and EV charging. An amp result here does not confirm that existing wiring is suitable.
Frequently asked questions
Can I calculate amps from watts without voltage?
No. The same wattage draws different current at different voltages. AC also needs the correct phase mode and power factor.
Does 1,500 watts always mean 12.5 amps?
No. That result applies at 120 V DC, or 120 V single-phase AC with PF 1. At PF 0.8, the same single-phase load draws 15.625 A.
Can I use 120 V line-to-neutral in the three-phase mode?
No. Enter line-to-line voltage. For a 120/208 V balanced three-phase supply, this mode uses 208 V and the total three-phase active power.
Does this tell me the breaker size?
No. Breaker selection requires the equipment instructions, load characteristics, conductor protection, and applicable installation requirements. Do not round the calculated amps to a breaker rating.
Are my calculation and PDF saved online?
The calculation and PDF generation run in your browser. The tool does not upload your inputs or save a calculation history. Download a PDF if you want to keep the current result.
