Skip to content

Square Footage Calculator

Enter your measurements in feet, inches, or metric units. This square footage calculator combines sections, subtracts cutouts, and shows totals for planning flooring, tile, paint, or other surface work.

Area 1
Name this area
Combine more areas

For several rooms or an irregular surface, add non-overlapping sections.

Subtract openings and excluded areas

Do not duplicate exclusions. An L-shaped area's corner cutout is already subtracted. Without coordinates, this tool cannot check overlaps or the location of exclusions.

Add a material allowance

Planning area is separate from the physical net area. No allowance is included by default.

Add an area-based cost estimate
Blank = no estimate; 0 = a zero rate.
For example: Material rate or Installed rate.

One rate applies to the whole selected area. Only the scope you assign to that rate is included; no tax, delivery, removal or market price is added.

Room Square Footage Calculator: Measure Each Section

Measure the surface you intend to cover. For a rectangular room, run a tape along two adjoining sides and record the length and width. Keep the tape straight and measure at the same level; furniture edges can make unreliable reference points. Multiply the two dimensions after converting them to the same unit.

A room area calculator can help compare spaces, but the measurements still need to match the job. For new flooring, include closets or alcoves that will receive the same product. Leave out a separate space if it is outside your project. Note any fixed cabinets before deciding which portions need covering.

Enter Feet, Inches, or Mixed Measurements

Choose Dimension units before entering values. To calculate square footage from measurements in inches, select inches (in) and enter each dimension in full. A 144 × 120 in rectangle is 17,280 in²; divide by 144 to get 120 ft². Dividing by 12 would convert only one linear dimension, not the product of two.

For measurements in feet and inches, select feet and inches under Dimension units. Enter each dimension in its separate ft and inches fields. For example, 10 ft 6 in equals 10.5 ft, not 10.6 ft. Twelve inches equal one foot; excess inches normalize when you select Calculate.

Use decimals for fractions: enter 5.5 instead of 5 1/2. Numeric fields do not accept combined strings such as 10′ 6". Meters, centimeters, and millimeters are also available. Changing a unit selector converts valid existing dimensions, so do not convert the numbers again yourself.

Floor Area Calculator: Combine Sections and Subtract Cutouts

Sketch an irregular outline and divide it into supported shapes without overlaps. Open Combine more areas, then select Add area for each additional section. Give each one a name if that will help you recognize it in the results. A rectangle plus a triangle may describe a bay; two adjoining rectangles can describe an L.

Alternatively, choose L-shaped area and enter the outer rectangle plus its missing rectangular corner. That corner is already deducted. Do not enter it again under exclusions. The diagrams identify the required dimensions; they are not drawn to scale.

ShapeCalculationWhat to measure
Rectanglelength × widthTwo adjoining, perpendicular sides
Circleπ × (diameter ÷ 2)²Across the center, not the radius
Trianglebase × height ÷ 2Height perpendicular to the base
Trapezoid(side A + side B) × height ÷ 2Both parallel sides and the perpendicular distance between them
L-shaped outlineouter length × outer width − cutout length × cutout widthOuter dimensions and a corner cutout that fits inside them

Open Subtract openings and excluded areas to remove a column footprint or another portion you will not cover. Each exclusion can use a supported shape or a known measurement with its square unit. Keep deductions within the included surfaces and count each one once. The tool sums entries; it cannot detect intersections or check where a cutout lies.

Example: Two Sections with One Exclusion

After Reset, enter a 12 × 10 ft rectangle. Add a second, adjoining 10 × 8 ft rectangle with no overlap. Add a Known area exclusion of 20 ft² for a portion inside those sections that will not receive the finish.

The included total is 120 + 80 = 200 ft². Subtracting 20 leaves 180 ft², or 20 yd² and approximately 16.72 m². Turn on a 10% material allowance to get a separate planning total of 198 ft²; the measured net stays 180 ft².

Read the Result and Plan the Purchase

The sq ft calculator shows the net measurement first, followed by square yards and square meters. Gross is the sum of included sections; excluded is the sum of deductions. Their difference is the net. An exclusion larger than the included total is rejected; equal totals produce zero.

Results from the square feet calculator use these conversions: 9 ft² = 1 yd² and 1 ft² = 0.09290304 m². Open Acres and hectares for larger units. Dimensions convert to feet before multiplication, and calculations keep full precision before the display is rounded. Extra decimal places do not make a tape measurement more accurate.

Use the floor square footage calculator to measure the space, then check how much material to order. Buying quantities also depend on cuts, product coverage, and whole packages. No extra percentage is added by default. If you enable an allowance, the planning total is net × (1 + percentage ÷ 100); choose that percentage for your material and layout.

Take the total to the Flooring Calculator for whole boxes, or the Tile Calculator for tile and package quantities. Check the supplier’s coverage and ordering rules before purchasing. Keep your sketch and original measurements with the estimate so you can recheck an unusual corner without starting over.

Optional pricing accepts one USD rate per ft², yd², or m². Choose whether it applies to the net or planning total. In the example, $5 per ft² gives $900 on net or $990 with the allowance. A blank price means cost is unknown; 0 is a known zero rate. Taxes, delivery, removal, and other charges are not added automatically.

Frequently Asked Questions

How do I subtract windows and doors for painting?

Measure each wall’s horizontal span and vertical height, then enter openings as exclusions. A room’s footprint does not establish its wall coverage. Use the Paint Calculator when you need gallons based on coats and product coverage.

Can I estimate a curve that is not a full circle?

Use the square footage estimator for a rough plan by dividing the outline into smaller supported shapes. For the circle option, enter the diameter; the calculator returns the area of a full circle. For a partial curve, the approximation depends on your sketch; the tool does not reconstruct arbitrary boundaries or read plans.

Why did my previous result disappear?

Editing an input clears the previous estimate so it cannot be mistaken for the updated one. Select Calculate again. Reset removes added sections and exclusions, clears dimensions and price, and restores the initial settings.

Can I use this as official residential floor area?

Use it for project planning. Adding interior dimensions does not certify a property’s official size for appraisal or sale. The measurement rules depend on the purpose and applicable standard; arrange the appropriate measurement when that distinction matters.