Skip to content

Gutter Cost Calculator

Use this gutter cost calculator to replace old gutters, install gutters on an addition, or check a contractor’s quote. Enter gutter lengths, downspout details, and your prices to see order quantities and a line-by-line estimate.

Gutter measurements

Downspouts

Use the count from your layout or quote. Group downspouts with the same length and pricing. Gutter sizing and drainage capacity are outside this estimate.

Gutter order and price

Each run is rounded up separately. Reusing offcuts depends on your cut list.

Fittings

Enter the counts from your layout or material list. Leave quantities blank for parts outside this estimate.

Prices are optional. Enter 0 for a confirmed $0.00 charge. The example uses illustrative prices and replaces the current entries.

How to Use the Gutter Estimate Calculator

Choose Materials Only when you are ordering sectional gutters and fittings. Use Installed Estimate when you have a contractor’s rate per linear foot or a fixed quote. Both modes keep the length along the roof edge separate from the length of the downspouts. Enter the prices from your supplier or contractor in dollars. You can also calculate the quantities first and fill in prices later.

Choose Individual runs if you have the length of each straight stretch of gutter. In Materials Only, this lets you count whole sections for each run. If you have a measurement sheet or proposal with a single total, choose Known total and enter the gutter footage from that document. With one total you can estimate cost by the foot or use a contractor’s fixed price. To get a count of whole sections or packages of sections, go back to the individual runs and check how the supplier sells the product.

Enter downspouts from your layout or quote. Add one row for a single downspout, or use the quantity field for several with the same length and pricing. For example, if the back of an addition has one 9 ft downspout and the front has two 12 ft downspouts, use two rows. The calculator reports three downspouts and 33 linear ft of downspout length while leaving the gutter footage unchanged.

What to Measure Before Using the Gutter Estimator

Sketch the roof edges that will have gutters and label each straight run. On a simple addition, you may need only the two long eaves. On a house with a porch or a garage set back from the front wall, keep those edges on separate lines of the sketch. Measure along the intended gutter path and start a new run where the gutter turns a corner or stops. A dimension from the foundation plan can miss a roof overhang or include a gap between two runs.

Mark the downspout locations on the same drawing. Write down the length specified for each drop and note where the quote calls for elbows, extensions, or a connection to existing drainage. If the installer’s measurement includes an offset or extension, ask which pieces are included in that length and which appear as separate items. A taller drop can change your downspout order even when the two gutters above it have identical lengths.

Use a confirmed layout or contractor proposal for the number and placement of downspouts. Gutter size, downspout count for a particular roof, and drainage capacity are design decisions outside this estimate. If you are still deciding how the roof will drain, confirm the layout before you turn the quantities into an order.

How the Gutter Cost Estimator Prices Materials and Labor

For a sectional order, enter the length of one stock section. The calculator divides each run by that length, rounds up to the next whole section when needed, and adds the section counts. A 20 ft run takes two 10 ft sections. A run slightly longer than 20 ft takes three under this method. Each run is treated separately. If you plan to use a leftover piece on another run, check the cut list and connector locations before you reduce the order.

Choose the price unit that matches the supplier’s quote. A price per section applies to the whole section count. If the supplier lists a price per linear foot but ships whole sections, use the whole-section option and enter the rate per foot. The rate applies to the length of the sections you buy. For an early estimate based on measured footage, choose Price by measured length. That choice uses the measured gutter length and leaves section quantities for later.

Enter quantities for corners, end caps, and connectors from the layout or supplier list. The price per piece applies to each quantity you enter. Check whether the end caps are handed and whether the supplier counts corner assemblies and the connectors that attach them as separate items. The count that comes out of a sectional gutter calculation gives you the stock lengths. The fittings still depend on how you join those lengths and finish each run.

What to Include in a Gutter Replacement Cost Calculator

Start with the contractor’s base line item and read the scope that goes with it. Make a note of whether the price covers removing the old gutters, hauling them away, repairing the fascia, and installing the new downspouts. Mark each included item as Included in base quote so the estimate records it without adding a second charge. Use Charged separately for a line billed on top of the base price. If the quote says fascia repairs will be priced after removal, leave that separate price blank until you have a figure.

Before ordering or signing, check the start and end points of every run, the total being billed, the downspout list, the parts the supplier will ship, and any allowances the contractor can adjust on site. Two bids can cover the same gutter footage while one includes disposal and the other charges for it separately. A written scope also helps when one installer is reusing existing downspouts and another is replacing them.

If the roof and gutters will be replaced together, use the Metal Roof Cost Calculator to estimate the roofing scope separately. Roofing is calculated from roof area. Use the roof-edge length here for the gutters, and check which contractor is responsible for removing and reinstalling them.

When damaged siding will be repaired along with the gutters, use the Siding Calculator to work out the exterior wall area and siding material cost separately. Ask the contractor to specify which work belongs to the fascia line and which wall sections are included in the siding scope.

How to Use the Seamless Gutter Cost Calculator

For a seamless system, choose Installed Estimate and enter the contractor’s rate per linear foot or fixed price. The rate uses the measured gutter footage by default. If the proposal gives a different billable quantity, enter the proposal’s footage in the billed-length field. With a fixed quote, the base price is entered once as one job or package. Both methods use the lengths for reference without rounding them to retail sections.

Two proposals at the same per-foot rate can come to different totals. Check the billed length first, then compare the rate’s scope. A contractor may quote the same measured length on both proposals and use different billed quantities because one includes a minimum. The base rate might also cover materials and installation in one proposal and labor alone in another. Check downspouts, tear-off, disposal, repairs, and other charges before comparing the totals.

Worked Example From Eave Measurements to a Quote

The rates below are illustrative. Use Load example in the form to enter the same measurements and prices. Start with three straight runs of 24, 31, and 17 ft. They add up to 72 linear ft of gutter. Two 12 ft downspouts add up to 24 linear ft of downspouts, reported separately.

For the materials order, suppose the supplier sells 10 ft sections. The 24 ft run takes three, the 31 ft run takes four, and the 17 ft run takes two. Order nine sections, or 90 linear ft of stock. At $24 per section, the gutter line is $216.00. A supplier price of $2.40 per linear ft for those same whole sections gives the same amount, because it applies to all 90 ft. The example leaves the downspout price open, so $216.00 is the known subtotal.

For a separate installed quote, suppose a contractor offers seamless gutters at $12 per linear ft with materials and installation included. The quote uses 72 ft, which comes to $864.00. The downspouts are included. Add $150.00 for separately billed removal and disposal, and the entered estimate totals $1,014.00.

Frequently Asked Questions

Can I get a section count from total footage alone?

Enter the individual runs for a whole-section count. A total of 72 ft might need eight 10 ft sections for one continuous run, while the three runs in the example take nine. A total alone works for an estimate priced by measured footage.

What happens when I leave a price blank?

The item stays unpriced. If another line has a price, the estimate shows a Known subtotal and names the unpriced lines. If every price is blank, you still get quantities. Enter 0 for a confirmed zero-dollar line.

Can I compare a fixed quote with a per-foot quote?

Calculate and download each quote with its own price type and billed scope. Check that both cover the same runs and downspouts, then compare the included and separately billed lines before deciding which total is lower for the work you need.

When can I download a PDF?

Calculate first to download a summary of your measurements, price basis, and results. After editing the form or selecting Reset, calculate again to export the updated estimate. The calculator and PDF run in your browser.